lopquote.blogg.se - Directions to open sentry safe

#Directions to open sentry safe how to#
#Directions to open sentry safe full#
#Directions to open sentry safe plus#

Baum brand antique safes most often use the same sequence as Group 2 locks, even though they are not Group 2:Īntique Safes by National Safe and Hall SafeĪntique National brand safes normally use the following procedure, while antique Hall units normally use the reverse of it. The last move to the right draws back the bolts to unlock the safe.Īntique Safes by Cary Safe, Detroit Safe and J. If there is a safe handle, turn it after going to the last number. Turn right to draw back the safe bolts to unlock the safe.Locksmiths often re-wrote the combinations to a simpler procedure, the second version shown. Original factory instructions showed the first sequence shown below, possibly to give the illusion that these units are more secure than they are. Victor brand safes are a common brand of antique safes. On these safes the dial won’t automatically come to a stop on the last movement – you need to dial to the number and stop. If the sequence below does not work, reverse the directions so that you start to the left. In addition to the dial, these usually have a thumb turn or key that draws back the safe bolts. Gardall Brand Microwave Safes & Other Recent Korean and Chinese Low-End Fire Safes If there is no safe handle, then turning the dial back to the Right again will unlock the safe. A very small number start to the right, then left, then right. A small number of these have Group 2 locks, but most have direct entry lock systems which use the following procedure. Sentry safes are the most common safes on the market. These locks are rare it is very unlikely you have one of these. Manufacturer’s combination cards often show a fourth number – this is the same number at which the dial will stop.You will feel the lock “engage” about eight numbers before it stops.

#Directions to open sentry safe full#

If you dialed correctly, the dial will stop in less than one full turn.

Turn the dial Right until the dial stops.

Turn the dial Left to the third number 2 times.

Turn the dial Right (clockwise) to the second number 3 times.

Turn the dial Left (counter clockwise) to the first number 4 times.

This procedure will work for all of them: How Do I Open My Combination Lock Safe? Group 2 Locks with 3 Wheelsĩ8% of all Group 2 locks have three “wheels” inside. It sometimes helps to tap on the safe door while dialing. When you get to the last number, try jiggling the dial back & forth.

If you think you have the combo but cannot get it to work, especially with an old safe, try the numbers you have 10 times.

They may not have been serviced in 50 years, during which time the lubrication can turn sticky. They might make lots of noise and they might not turn smoothly.

Old lock technology was not as good as it is now, and your lock may be worn out.

If you go past that number, you need to start the dialing procedure over.

If you go slightly past the number you are dialing to, it is not ok to just back up those few numbers.

(Older locks are typically a little more forgiving.)

#Directions to open sentry safe plus#

When you come to the number you are dialing to, you must be accurate – plus or minus one half of the space to the next mark.

You do not go past the number 4 or 3 or 2 times, you go to the number 4, 3 or 2 times.

It does not matter where you start from it makes no difference which number is at the indicator mark when you start.

Dial to the indicator mark which is at the 12:00 position, not the one at 11:00.

Dialing Procedure Checklist for Mechanical Combination Safe Locks

If you have this type of lock, call us while you are standing next to your safe for additional instructions. Procedures for very high security locks like Group 2M, Group 1 and Group 1M are too complicated to show. Go to the Safe Lock Identification page to help figure out what you have, then come back to this section and look for the correct dialing procedure. The first step is to determine which type of lock you have. There are many different types of combination locks so there are also many different dialing sequences.

#Directions to open sentry safe how to#

This section will help you determine how to open your combination lock. They may have the numbers, but don’t know how many turns to the left or right. Customers frequently need the proper dialing procedures for their safes.